P161d nissan qashqai ошибка

Qashqai J11. Security control system — part 16

Check DTC in “Self Diagnostic Result”mode of “ENGINE”using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479738

When BCM detects an immobilizer malfunction and engine start is prohibited.

[WITHOUT INTELLIGENT KEY SYSTEM]

INFOID:0000000010479739

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Check DTC in “Self Diagnostic Result”mode of “ENGINE” using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479740

Using CONSULT, register ECM.
Is the DTC detected?

Replace ECM.
Refer to the following procedure.
• HRA2DDT:

When CONSULT is not used during ECM replacement.

[WITHOUT INTELLIGENT KEY SYSTEM]

INFOID:0000000010479741

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Check DTC in “Self Diagnostic Result”mode of “ENGINE”using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479742

Replace ECM.
Refer to the following procedure.
• HRA2DDT:

When BCM detects an immobilizer malfunction and engine start is prohib-
ited.

[WITHOUT INTELLIGENT KEY SYSTEM]

INFOID:0000000010479743

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON and wait 2 seconds or more.

Check DTC in “Self Diagnostic Result”mode of “ENGINE”using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479744

Select “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

Perform DTC CONFIRMATION PROCEDURE for DTC P1616. Refer to

Is DTC P1616 displayed again?

Replace ECM.
Refer to the following procedure.
• HRA2DDT:

ECM ROM is malfunctioning

B2190 CHAIN OF BCM — IMM ANT

[WITHOUT INTELLIGENT KEY SYSTEM]

B2190 CHAIN OF BCM — IMM ANT

INFOID:0000000010479745

Security indicator lamp turn ON

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Make the conditions that BCM enters in the low power consumption mode (BCM sleep condition).
Refer to

Check to DTC in “Self Diagnostic Result” mode of “BCM” CONSULT.

Читайте также:  Volkswagen touareg tdi 2015

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479746

IGNITION KEY REGISTRATION

Using CONSULT, register all Ignition Keys again.

PERFORM SELF-DIAGNOSIS RESULT

Select “Self Diagnosis Result” mode of “BCM” using CONSULT.

Perform DTC CONFIRMATION PROCEDURE for B2190. Refer to

CHECK NATS ANTENNA COMMUNICATION SIGNAL

Check voltage signal between NATS antenna amp. harness connector and ground using an oscilloscope.

Is the inspection result normal?

>> Replace NATS antenna amp. Refer to

When BCM cannot detect the immobilizer ID in 0.6 seconds.

Just after inserting igni-
tion key into key cylinder

Pointer of tester should move

Just after inserting igni-
tion key into key cylinder

Pointer of tester should move

[WITHOUT INTELLIGENT KEY SYSTEM]

B2190 CHAIN OF BCM — IMM ANT

CHECK NATS ANTENNA COMMUNICATION SIGNAL CIRCUIT

Disconnect BCM connector and NATS antenna connector.

Check continuity between NATS antenna amp. harness connector and BCM harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

>> Repair or replace harness.

B2191 ID DISCORD, BCM — IMM ANT

[WITHOUT INTELLIGENT KEY SYSTEM]

B2191 ID DISCORD, BCM — IMM ANT

INFOID:0000000010479747

Security indicator lamp turn ON

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Check to DTC in “Self Diagnostic Result” mode of “BCM” CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479748

IGNITION KEY REGISTRATION

Using CONSULT, register all Ignition Keys again.
Can engine be started with the registered Ignition Key?

Prepare Ignition Key that matches the vehicle.

Registration of all Ignition Key using CONSULT.

Can engine be started with the registered Ignition Key?

CHECK INTERMITTENT INCIDENT

When BCM continuously cannot detect inconsistency of Immobilizer ID in
0.6 seconds or more.

[WITHOUT INTELLIGENT KEY SYSTEM]

B2192 ID DISCORD, IMMU-ECM

INFOID:0000000010479749

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Читайте также:  Подогрев лобового стекла lexus rx

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479750

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?

CHECK SELF DIAGNOSTIC RESULT

Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

Perform DTC CONFIRMATION PROCEDURE for DTC B2192. Refer to

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

Replace ECM.
Refer to the following procedure.
• HRA2DDT:

The ID verification results between BCM and ECM are NG.

B2192 ID DISCORD, IMMU-ECM

[WITHOUT INTELLIGENT KEY SYSTEM]

[WITHOUT INTELLIGENT KEY SYSTEM]

B2193 CHAIN OF ECM-IMMU

INFOID:0000000010479751

(The CAN communication line is open or shorted.)

DTC CONFIRMATION PROCEDURE

If DTC B2193 is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000 or
U1010.

Is applicable DTC detected?

>> Perform diagnosis of applicable. U1000: Refer to

PERFORM DTC CONFIRMATION PROCEDURE

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479752

If DTC B2193 is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000 or
U1010.

Is applicable DTC detected?

>> Perform diagnosis of applicable. U1000: Refer to

Can the system be initialized and can the engine be started with registered Intelligent Key?

Replace ECM.
Refer to the following procedure.
• HRA2DDT:

Inactive communication between BCM and ECM

B2193 CHAIN OF ECM-IMMU

[WITHOUT INTELLIGENT KEY SYSTEM]

[WITHOUT INTELLIGENT KEY SYSTEM]

INFOID:0000000010479753

ID verification request out of the specified specification

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Читайте также:  Замена масла вариатор lifan x60

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479754

CHECK SELF DIAGNOSTIC RESULT 1

Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

Perform DTC CONFIRMATION PROCEDURE for DTC B2195. Refer to

CHECK EQUIPMENT OF THE VEHICLE

Check that unspecified accessory part related to engine start is not installed.

Is unspecified accessory part related to engine start installed?

CHECK SELF DIAGNOSTIC RESULT 2

Obtain the customers approval to remove unspecified accessory part related to engine start, and then
remove it.

Select “Self Diagnostic Result” of “BCM” using CONSULT.

Perform DTC CONFIRMATION PROCEDURE for DTC B2195. Refer to

ID verification between BCM and ECM that is out of the specified
specification is detected.

[WITHOUT INTELLIGENT KEY SYSTEM]

INFOID:0000000010479755

BCM performs ID verification between BCM and dongle unit.
When verification result is OK, BCM permits cranking.

INFOID:0000000010479756

(Dongle unit circuit is open or shorted.)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Check DTC in Self-diagnosis result mode of BCM using CONSULT.

>> To check malfunction symptom before repair: Refer to

>> Confirmation after repair: INSPECTION END

INFOID:0000000010479757

Perform initialization of BCM and registration of all mechanical keys using CONSULT.
For initialization and registration procedures, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.

CHECK DONGLE UNIT CIRCUIT

Disconnect BCM connector and dongle unit connector.

Check continuity between BCM harness connector and dongle unit harness connector.

Check continuity between BCM harness connector and ground.

The ID verification results between BCM and dongle unit is invalid.

[WITHOUT INTELLIGENT KEY SYSTEM]

Is the inspection result normal?

>> Repair or replace harness.

CHECK DONGLE UNIT GROUND CIRCUIT

Check continuity between dongle unit harness connector and ground.

Is the inspection result normal?

>> Repair or replace harness.

Источник

Оцените статью
Adblock
detector