Ошибка c1340 mitsubishi l200

Содержание
  1. Code No.C1340: Stop lamp switch circuit malfunction
  2. STEP 2. Diagnosis code recheck after resetting CAN bus lines
  3. Q. Is the diagnosis code No.C1340 set?
  4. STEP 3. Stop lamp and high-mount stop lamp operation check
  5. Q. Is the check result normal?
  6. STEP 4. Connector check: C-139 stop lamp switch connector
  7. Q. Is the check result normal?
  8. STEP 5. Check for stop lamp switch installation
  9. Q. Is the check result normal?
  10. STEP 6. Stop lamp switch continuity check
  11. Q. Is the check result normal?
  12. STEP 7. Connector check: A-68 ASTC-ECU connector, C-02 joint connector, F-02 rear combination lamp (stop: LH) connector, F-10 rear combination lamp (stop: RH) connector, F-06 high mounted stop lamp connector, C-15 intermediate connector, C-18 intermediate connector
  13. Q. Is the check result normal?
  14. STEP 8. Voltage measurement at C-139 stop lamp switch connector.
  15. Q. Is the check result normal?
  16. STEP 9. Resistance measurement at C-139 stop lamp switch connector.
  17. Q. Is the check result normal?
  18. STEP 10. Resistance measurement at C-139 stop lamp switch connector and C-02 joint connector.
  19. Q. Is the check result normal?
  20. STEP 11. Voltage measurement at A-68 ASTC-ECU connector.
  21. Q. Is the check result normal?
  22. Code No.C1340: Open Circuit Abnormality of Stoplamp Switch
  23. STEP 2. Check whether the diagnosis code is reset.
  24. Q. Is code No.C1340 set?
  25. STEP 3. Operation check of stop lamp
  26. Q. Is the check result normal?
  27. STEP 4. Check of stop lamp switch
  28. Q. Is the check result normal?
  29. STEP 5. Voltage measurement at ASTC-ECU connector A-48.
  30. Q. Is the check result normal?
  31. STEP 6. Check ASTC-ECU connector A-48, stop lamp switch connector C-114, junction connector C-10 and intermediate connector C-13 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
  32. Q. Is the check result normal?
  33. STEP 7. Check whether the diagnosis code is reset.
  34. Q. Is code No.C1340 set?
  35. STEP 8. Check whether the diagnosis code is reset.
  36. Q. Is code No.C1340 set?
  37. Code No.C1340: Stop lamp switch circuit malfunction
  38. STEP 2. Diagnosis code recheck after resetting CAN bus lines
  39. Q. Is the diagnosis code No.C1340 set?
  40. STEP 3. Stop lamp and high-mount stop lamp operation check
  41. Q. Is the check result normal?
  42. STEP 4. Connector check: C-114 stop lamp switch connector
  43. Q. Is the check result normal?
  44. STEP 5. Check for stop lamp switch installation
  45. Q. Is the check result normal?
  46. STEP 6. Stop lamp switch continuity check
  47. Q. Is the check result normal?
  48. STEP 7. Connector check: A-48 ASTC-ECU connector, C-13,C-10 joint connector, C-30 intermediate connector, F-02 rear combination lamp (stop: RH) connector (with rear body), F-19 rear combination lamp (stop: RH) connector (without rear body), F-03 high mounted stop lamp connector (with rear body), F-04 rear combination lamp (stop: LH) connector (with rear body), F-23 rear combination lamp (stop: LH) connector (without rear body), F-07 intermediate connector
  49. Q. Is the check result normal?
  50. STEP 8. Voltage measurement at C-114 stop lamp switch connector.
  51. Q. Is the check result normal?
  52. STEP 9. Resistance measurement at C-114 stop lamp switch connector.
  53. Q. Is the check result normal?
  54. STEP 10. Resistance measurement at C-114 stop lamp switch connector and C-10 joint connector.
  55. Q. Is the check result normal?
  56. STEP 11. Voltage measurement at A-48 ASTC-ECU connector.
  57. Q. Is the check result normal?
  58. STEP 12. Diagnosis code recheck
  59. Q. Is the diagnosis code No.C1340 set?
  60. STEP 13. Diagnosis code recheck
  61. Q. Is the diagnosis code No.C1340 set?
Читайте также:  Тойота пикап американский рынок

Code No.C1340: Stop lamp switch circuit malfunction

STEP 2. Diagnosis code recheck after resetting CAN bus lines

Q. Is the diagnosis code No.C1340 set?

STEP 3. Stop lamp and high-mount stop lamp operation check

Q. Is the check result normal?

STEP 4. Connector check: C-139 stop lamp switch connector

Q. Is the check result normal?

STEP 5. Check for stop lamp switch installation

Q. Is the check result normal?

STEP 6. Stop lamp switch continuity check

Q. Is the check result normal?

Replace the stop lamp switch (Refer to GROUP 35A — Brake Pedal .) Then go to Step 13.

STEP 7. Connector check: A-68 ASTC-ECU connector, C-02 joint connector, F-02 rear combination lamp (stop: LH) connector, F-10 rear combination lamp (stop: RH) connector, F-06 high mounted stop lamp connector, C-15 intermediate connector, C-18 intermediate connector

Q. Is the check result normal?

STEP 8. Voltage measurement at C-139 stop lamp switch connector.

Q. Is the check result normal?

STEP 9. Resistance measurement at C-139 stop lamp switch connector.

Q. Is the check result normal?

STEP 10. Resistance measurement at C-139 stop lamp switch connector and C-02 joint connector.

Q. Is the check result normal?

STEP 11. Voltage measurement at A-68 ASTC-ECU connector.

Q. Is the check result normal?

An open circuit in signal line has occurred in the wiring harness between A-68 ASTC-ECU connector terminal No.7 and C-02 joint connector terminal No.1, therefore, repair it. Then go to Step 13.

Источник

Code No.C1340: Open Circuit Abnormality of Stoplamp Switch

Repair the CAN bus line (Refer to GROUP 54C, CAN bus line Diagnostic flow ). Then go to Step 2.

Читайте также:  Ford ranger тюнинг raptor

STEP 2. Check whether the diagnosis code is reset.

Q. Is code No.C1340 set?

The procedure is complete.

STEP 3. Operation check of stop lamp

Q. Is the check result normal?

STEP 4. Check of stop lamp switch

Q. Is the check result normal?

STEP 5. Voltage measurement at ASTC-ECU connector A-48.

Q. Is the check result normal?

STEP 6. Check ASTC-ECU connector A-48, stop lamp switch connector C-114, junction connector C-10 and intermediate connector C-13 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q. Is the check result normal?

An open or short circuit may be present between the stop lamp switch and ASTC-ECU. Repair the wiring harness between ASTC-ECU connector A-48 terminal 7 and stop lamp switch connector C-114 terminal 1. Then go to Step 8.

Repair or replace the damaged component(s). Then go to Step 8.

STEP 7. Check whether the diagnosis code is reset.

Q. Is code No.C1340 set?

Replace the hydraulic unit assembly (integrated with ASTC-ECU). Then go to Step 8.

It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points — How to Cope with Intermittent Malfunction .

STEP 8. Check whether the diagnosis code is reset.

Q. Is code No.C1340 set?

The procedure is complete.

Источник

Code No.C1340: Stop lamp switch circuit malfunction

STEP 2. Diagnosis code recheck after resetting CAN bus lines

Q. Is the diagnosis code No.C1340 set?

STEP 3. Stop lamp and high-mount stop lamp operation check

Q. Is the check result normal?

STEP 4. Connector check: C-114 stop lamp switch connector

Q. Is the check result normal?

STEP 5. Check for stop lamp switch installation

Q. Is the check result normal?

STEP 6. Stop lamp switch continuity check

Q. Is the check result normal?

Replace the stop lamp switch (Refer to GROUP 35A — Brake Pedal .). Then go to Step 13.

Читайте также:  Пикап всех моделей девушек

STEP 7. Connector check: A-48 ASTC-ECU connector, C-13,C-10 joint connector, C-30 intermediate connector, F-02 rear combination lamp (stop: RH) connector (with rear body), F-19 rear combination lamp (stop: RH) connector (without rear body), F-03 high mounted stop lamp connector (with rear body), F-04 rear combination lamp (stop: LH) connector (with rear body), F-23 rear combination lamp (stop: LH) connector (without rear body), F-07 intermediate connector

Q. Is the check result normal?

STEP 8. Voltage measurement at C-114 stop lamp switch connector.

Q. Is the check result normal?

STEP 9. Resistance measurement at C-114 stop lamp switch connector.

Q. Is the check result normal?

STEP 10. Resistance measurement at C-114 stop lamp switch connector and C-10 joint connector.

Q. Is the check result normal?

STEP 11. Voltage measurement at A-48 ASTC-ECU connector.

Q. Is the check result normal?

STEP 12. Diagnosis code recheck

Q. Is the diagnosis code No.C1340 set?

STEP 13. Diagnosis code recheck

Q. Is the diagnosis code No.C1340 set?

© Automotive Manuals. All rights reserved.

Источник

Оцените статью
Adblock
detector