No turn signals jeep cherokee

1999 Jeep Cherokee Turn signals/Hazard lights

When I turn on the left turn signal, the rear(only) hazard flashers also come on(left & right). If I turn the hazard flasher button on and then off again the problem stops(front & rear left signals still work normaly). When I «hold» the left turn signal lever and not «click» it. Front & left signals still work normally. No problem with the right turn signals. I suspect the problem is in the steering column. Any one else ever complain of this?

2 Replies

I have the same problem with my ’98 Cherokee. Looking forward to the answer. How much of a donation do you folks need?

Neither my local AutoZone or Advance Auto Parts had a new turn signal switch in stock. So I did what any good old Kentucky boy does and fixed mine. The sticker on it said «Assembled in Mexico», but thank God they used four Torx head screws to hold it together.

Not a job recommended for everyone, but I got it apart and cleaned the contacts with dilute HCL acid and then relubed it with dielectric grease. Most of the contact surfaces were corroded with that green goo that gets on copper. Seems to be working fine, for now.

My advice would be to spend the $50 and buy a new switch, but I usually do things the hard way.

Please login or register to post a reply.

Related Turn Signal Not Working Content

1999 Jeep Cherokee Turn Signals

Electrical Problem 1999 Jeep Cherokee Turn Signals Do Not Work At All. All Other Lights Work Fine But No Turn Signals Or Hazard.

Turn signals are intended to help inform surrounding drivers of the vehicle’s intended change in direction. Although there are a few different causes for signal failure.

Turn Signals Not Working

There Is An Ongoing Discussion About A Similar Issue. Once Upon A Time, I Was Messing With Some Fuses In The Jeep To Test A Battery Drain.

Flashers And Signal Light Not Working

I Have A 1999 Jeep Grand Cherokee With 180000 Miles And My Flashers Nor My Signal Light Work. It Does Not Flash Nor Do They Come On. My.

No Blinkers Help.

I Have A 1985 Jeep Cherokee, My Blinkers Do Not Work. The Fuse Box Is A Mess. The Stop Where My Blinker Fuse Is, Is Missing A Prong. Dont.

My Blinkers Do Not Work At All Not Even The Indicators

When I Go To Switch My Blinkers On It Does Not Tell Me That They Are On And You Can’t See Them From Either The Back Or The Front Lights.

Источник

1999 Jeep Cherokee turn signals

The turn signals are out and I already replaced the turn signal switch but I have no idea what fuse to change out or where they go because I have no diagram for it.

1 Reply

Does the hazzard flasher lites work? Fuse 12—10 amp should be the turn fuse, interior fuse box.

Please login or register to post a reply.

Related Turn Signal Switch Content

1995 Jeep Cherokee Sport Turn Signal Problem

A turn signal switch is designed to activate the directional signals either right or left by the driver when desired.

Why Wont My Turn Signals Work On My 95 Jeep Cherokee 4.

It Started Off That My Headlights Wouldnt Work Out Of The Blue. So I Replaced The Headlights And They Still Didn’t Work. So I Put The Old.

1999 Jeep Cherokee Turn Signals

Electrical Problem 1999 Jeep Cherokee Turn Signals Do Not Work At All. All Other Lights Work Fine But No Turn Signals Or Hazard.

1999 Jeep Cherokee Left Turn Signal Problem

When I Use My Left Turn Signal, Both Of The Rear Turn Signals Blink(left And Right Side), This Happen Only To The Rear Of The Vehicle.

1999 Jeep Cherokee Turn Signals/hazard Lights

Electrical Problem 1999 Jeep Cherokee 6 Cyl Two Wheel Drive Automatic When I Turn On The Left Turn Signal, The Rear(only) Hazard.

Источник

How to change rear turn signal bulb on my Jeep Cherokee ?

Whether for your own security, for roadworthiness tests or to prevent a fine, making sure your turn signal bulbs are all the time functioning is very important. Indeed, bulbs are wearing parts that will predictably burn out with time and therefore need to be replaced. You’re probably here because one of your rear turn signals is burnt out and you’re trying to figure out how to change the bulb of a rear turn signal on you Jeep Cherokee, we’ve written and published this content to help you do it all on your own without having to go to your auto technician. In a first step, we will have a look at the checking a burnt-out rear turn signal bulb on your Jeep Cherokee and in a second step, how to replace the rear turn signal bulb on your Jeep Cherokee.

How to find out if the rear turn signal bulb on your Jeep Cherokee is burnt-out or needs to be replaced?

When you drive your vehicle you don’t all the time have the opportunity to examine all the security features of your Jeep Cherokee. Indeed, you are often times in a hurry and are likely to get into your vehicle, make your trip and put it down immediately without taking the time to do an occasional check-up. It is due to this fact essential to take the time to on occasions examine the condition of your headlights and turn signals. It’s quite possible that you have a burnt-out rear turn signal on your Jeep Cherokee, but you didn’t perceive it. Here are the two basic methods to examine if a rear turn signal on your car is out of order or if you need to replace it as soon as possible:

• When you stop, turn on the ignition on your Jeep Cherokee, then alternately turn on your left and right rear turn signals and get out of the car to examine that they are efficient.
• By paying attention to the sound of your turn signals. Indeed, there is an audible warning on each car that notifies you of a rear turn signal bulb burnt out on your Jeep Cherokee, you will detect that the time between each “click” is much shorter, this involves that you will have to replace the rear turn signal bulb or before. It’s up to you to check and verify which one is burnt out by a visual check as on the first strategy shown above.

You may have another bulb to replace, like the one of your low beam Jeep Cherokee or your position lights on Jeep Cherokee, don’t be reluctant to consult our content articles to help you to do this substitution.

Replacing the rear turn signal bulb on my Jeep Cherokee

Now let’s go to the most instersting step of this article, how to replace the rear turn signal bulb on Jeep Cherokee? Take note that this operation is fairly simple, you will need to access, from the inside of your trunk, your headlight unit, open it and change the burnt out rear turn signal bulb on your car. If it is a bulb on your front turn signal on your Jeep Cherokee, see our dedicated guideline. Nevertheless, here are the detailed steps to stick to to be able to execute this process correctly:

• To access the tail light assembly, take out the carpeting or plastic cover to access the tail light assembly.
• Use a screwdriver or torx wrench (6-pointed star) to open the tail light assembly.
• Take off the rear indicator bulb from your burnt-out turn signal that you have earlier in this article identified by an external visual inspection, for this you will need to make a quarter turn in a counter-clockwise way
• Change the rear turn signal bulb on your Jeep Cherokee. There are two kind of bulbs, transparent bulbs when the cover is orange, or orange bulbs when the cover is transparent, choose the right model for your car

If you want more guides on the Jeep Cherokee, go to our Jeep Cherokee category.

Источник

How to change front turn signal bulb on my Jeep Cherokee ?

Whether for your own safety, for roadworthiness testing or to avoid a fine, making sure your turn signal bulbs are always operational is very important. In fact, bulbs are wearing parts that will predictably burn out as time passes and consequently need to be swapped out. You’re probably on this site because one of your front turn signals is burnt out and you’re questioning how to change the bulb of a front turn signal on your Jeep Cherokee, we’ve written and published this article content to help you do it alone and independently and not have to go to your mechanic. In a first section, we will examine controling a burnt-out front turn signal bulb on your Jeep Cherokee and in a second section, how to change the front turn signal bulb on your car..

How to find out if the front turn signal bulb on your Jeep Cherokee is burnt out or needs to be changed?

• When you stop, turn on the ignition on your car, then alternately turn on your left and right front turn signals and get out of the car to verify that they are working.
• By hearing to the sound of your blinkers. In fact, there is an audible indicator on each car that warns you of a front turn indicator bulb burnt out on your Jeep Cherokee, you will perceive that the time between each “click” is much shorter, this suggests that you will have to swap the front turn signal bulb or before. It’s up to you to check and check out which one is burnt out by a visual verify as on the first technique shown earlier mentioned.

You may have another bulb to replace, like the one of your low beam or your position lights, don’t hesitate to read our blog posts to help you to carry out this substitution.

Changing the front turn signal bulb on your Jeep Cherokee

Now let’s go to the most important section of this article content, how to change the front turn signal bulb of your Jeep Cherokee? Please note that this technique is uncomplicated, you will require to access, from the inside of your bonnet, through the wheel arch, or simply by your bumper to your headlight unit, open it and change the burnt out front turn signal bulb of your Jeep Cherokee. If it is a bulb on your rear turn signal, see our specific article content. Nevertheless, here are the details of the steps to follow in order to carry out this act properly depending on the approach you wish to choose.

Change front turn signal bulb on your Jeep Cherokee through the bonnet:

• Open your bonnet and clear access to your headlight pods.
• Use a torx tip to open the headlight unit on your car
• Unscrew the front turn signal bulb from your car by turning it a quarter turn counterclockwise
• Replace the front flasher bulb of your Jeep Cherokee by the new one (be sure to check if it’s an orange or transparent bulb).
• Reassemble and test that the new front turn signal bulb functions.

Change the front turn signal bulb of your Jeep Cherokee through the wheel arch:

• Lift your car, and remove the front wheel on the side you want to work on.
• Take out your wheel arch with a torx bit.
• Go to your headlamp block and replace the front turn signal bulb on your car following the same steps as on the part previously seen.

Replace the front turn signal bulb of your Jeep Cherokee through the bumper:

• Put your Jeep Cherokee on a jack or a candle.
• Remove the screws of the motor shoe of your car(plastic part under your motor) and your shock absorber. Beware with the plastic staples which can be breakable.
• Remove your headlight block and replace the front turn indicator bulb of your Jeep Cherokee following the steps seen in the parts seen previously.
• Put the whole thing back together again.

To get more tips on the Jeep Cherokee, take a look at the Jeep Cherokee category.

Источник