P2765 nissan qashqai j11

Nissan Qashqai J11. Instruction — page 696

If another «DTC CONFIRMATION PROCEDURE» occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

(Trouble diagnosis content)

SELECT SOLENOID
(Select solenoid)

When any of 1, or 2 is satisfied:
1.

When all the following conditions are es-
tablished three times in 1DC

DTC other than the applicable DTC is not
detected.

Throttle position: More than 6.27 deg.

Vehicle speed: Less than 3 km/h (1
MPH)

CVT fluid temperature: More than 20

Selector lever: Other than P, N

Turbine speed when performed N

TCM power supply voltage: More than 11
V

When all of the following conditions are
satisfied and this state is maintained for
30 seconds:

The counting of time continues while all
of the following conditions are satisfied
and stops when the conditions become
unsatisfied (the count is maintained).
When accumulated time reaches 30 sec-
onds (Clutch is judged as engaged and
the count is reset.)

Selector lever: Other than P, N

Vehicle speed: Less than 3 km/h (1
MPH)

Differences between primary pulley
speed and secondary speed: Less than
120 rpm

Clutch instructions pressure: 0.95 MPa
or more

Differences between turbine speed and
input speed: Less than 200 rpm

Turbine speed – speed: More than 450
rpm

DTC other than the applicable DTC is
not detected.

TCM power supply voltage: More than 11
V

P2813 SELECT SOLENOID

Источник

Nissan Qashqai J11. Instruction — part 755

Check continuity between output speed sensor harness connector terminal and ground.

Is the inspection result normal?

>> Repair or replace malfunctioning parts.

Connect all of disconnected connectors.

Check frequency of output speed sensor.

Is the inspection result normal?

>> Check intermittent incident. Refer to

>> Replace output speed sensor. Refer to

DETECT MALFUNCTIONING ITEMS

Check the following items:
• Open circuit or short circuit in harness between ignition switch and output speed sensor. Refer to

• 10A fuse [No.74, located in fuse block (J/B)]. Refer to

Is the check result normal?

Читайте также:  Kia sorento режим smart

>> Check intermittent incident. Refer to

>> Repair or replace malfunctioning parts.

• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)

P2813 SELECT SOLENOID

INFOID:0000000010245653

NOTE:
DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF

DTC CONFIRMATION PROCEDURE

Be careful of the driving speed.

(Trouble diagnosis content)

SELECT SOLENOID
(Select solenoid)

When any of 1, or 2 is satisfied:
1.

When all the following conditions are es-
tablished three times in 1DC

DTC other than the applicable DTC is not
detected.

Throttle position: More than 6.27 deg.

Vehicle speed: Less than 3 km/h (1
MPH)

CVT fluid temperature: More than 20

Selector lever: Other than P, N

Turbine speed when performed N

TCM power supply voltage: More than 11
V

When all of the following conditions are
satisfied and this state is maintained for
30 seconds:

The counting of time continues while all
of the following conditions are satisfied
and stops when the conditions become
unsatisfied (the count is maintained).
When accumulated time reaches 30 sec-
onds (Clutch is judged as engaged and
the count is reset.)

Selector lever: Other than P, N

Vehicle speed: Less than 3 km/h (1
MPH)

Differences between primary pulley
speed and secondary speed: Less than
120 rpm

Clutch instructions pressure: 0.95 MPa
or more

Differences between turbine speed and
input speed: Less than 200 rpm

Turbine speed – speed: More than 450
rpm

DTC other than the applicable DTC is
not detected.

TCM power supply voltage: More than 11
V

P2813 SELECT SOLENOID

Источник

Nissan Qashqai J11. Manual — part 755

Check continuity between output speed sensor harness connector terminal and ground.

Is the inspection result normal?

>> Repair or replace malfunctioning parts.

Connect all of disconnected connectors.

Check frequency of output speed sensor.

Is the inspection result normal?

>> Check intermittent incident. Refer to

>> Replace output speed sensor. Refer to

DETECT MALFUNCTIONING ITEMS

Check the following items:
• Open circuit or short circuit in harness between ignition switch and output speed sensor. Refer to

• 10A fuse [No.74, located in fuse block (J/B)]. Refer to

Is the check result normal?

>> Check intermittent incident. Refer to

Читайте также:  Subaru forester при покупке

>> Repair or replace malfunctioning parts.

• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)

P2813 SELECT SOLENOID

INFOID:0000000010245653

NOTE:
DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF

DTC CONFIRMATION PROCEDURE

Be careful of the driving speed.

(Trouble diagnosis content)

SELECT SOLENOID
(Select solenoid)

When any of 1, or 2 is satisfied:
1.

When all the following conditions are es-
tablished three times in 1DC

DTC other than the applicable DTC is not
detected.

Throttle position: More than 6.27 deg.

Vehicle speed: Less than 3 km/h (1
MPH)

CVT fluid temperature: More than 20

Selector lever: Other than P, N

Turbine speed when performed N

TCM power supply voltage: More than 11
V

When all of the following conditions are
satisfied and this state is maintained for
30 seconds:

The counting of time continues while all
of the following conditions are satisfied
and stops when the conditions become
unsatisfied (the count is maintained).
When accumulated time reaches 30 sec-
onds (Clutch is judged as engaged and
the count is reset.)

Selector lever: Other than P, N

Vehicle speed: Less than 3 km/h (1
MPH)

Differences between primary pulley
speed and secondary speed: Less than
120 rpm

Clutch instructions pressure: 0.95 MPa
or more

Differences between turbine speed and
input speed: Less than 200 rpm

Turbine speed – speed: More than 450
rpm

DTC other than the applicable DTC is
not detected.

TCM power supply voltage: More than 11
V

P2813 SELECT SOLENOID

Источник

Qashqai J11. Transaxle & Transmission — part 38

Maintain the following conditions for 10 seconds or more.

INFOID:0000000010245652

CHECK OUTPUT SPEED SENSOR POWER CIRCUIT

Disconnect output speed sensor connector.

Check voltage between output speed sensor harness connector terminal and ground.

Is the inspection result normal?

CHECK OUTPUT SPEED SENSOR GROUND CIRCUIT

Check continuity between output speed sensor harness connector terminal and ground.

Is the inspection result normal?

>> Repair or replace malfunctioning parts.

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 1)

Check continuity between output speed sensor harness connector terminal and TCM harness connector
terminal.

Is the inspection result normal?

P2765 INPUT SPEED SENSOR B

>> Repair or replace malfunctioning parts.

Читайте также:  Subaru forester 2012 мануал

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 2)

Check continuity between output speed sensor harness connector terminal and ground.

Is the inspection result normal?

>> Repair or replace malfunctioning parts.

Connect all of disconnected connectors.

Check frequency of output speed sensor.

Is the inspection result normal?

>> Check intermittent incident. Refer to

>> Replace output speed sensor. Refer to

DETECT MALFUNCTIONING ITEMS

Check the following items:
• Open circuit or short circuit in harness between ignition switch and output speed sensor. Refer to

• 10A fuse [No.74, located in fuse block (J/B)]. Refer to

Is the check result normal?

>> Check intermittent incident. Refer to

>> Repair or replace malfunctioning parts.

• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)

P2813 SELECT SOLENOID

INFOID:0000000010245653

NOTE:
DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF

DTC CONFIRMATION PROCEDURE

Be careful of the driving speed.

(Trouble diagnosis content)

SELECT SOLENOID
(Select solenoid)

When any of 1, or 2 is satisfied:
1.

When all the following conditions are es-
tablished three times in 1DC

DTC other than the applicable DTC is not
detected.

Throttle position: More than 6.27 deg.

Vehicle speed: Less than 3 km/h (1
MPH)

CVT fluid temperature: More than 20

Selector lever: Other than P, N

Turbine speed when performed N

TCM power supply voltage: More than 11
V

When all of the following conditions are
satisfied and this state is maintained for
30 seconds:

The counting of time continues while all
of the following conditions are satisfied
and stops when the conditions become
unsatisfied (the count is maintained).
When accumulated time reaches 30 sec-
onds (Clutch is judged as engaged and
the count is reset.)

Selector lever: Other than P, N

Vehicle speed: Less than 3 km/h (1
MPH)

Differences between primary pulley
speed and secondary speed: Less than
120 rpm

Clutch instructions pressure: 0.95 MPa
or more

Differences between turbine speed and
input speed: Less than 200 rpm

Turbine speed – speed: More than 450
rpm

DTC other than the applicable DTC is
not detected.

TCM power supply voltage: More than 11
V

P2813 SELECT SOLENOID

Источник

Оцените статью
Adblock
detector