строение ремня я примерно знаю, вот между сегментами идут пластины будербродом они я так понял не цельные а держутся за щёт смещение концов вот как раз на одну такую пластину это и похоже, конешно могу ошибаться, вскрытие покажет)))
Вы можете задать вопрос или поделиться опытом устранения ошибки P0715 на автомобиле NISSAN с другими пользователями.
Возможную причину возникновения и советы по устранению можно найти в каталоге причин и советов:
Ошибки (коды ошибок) полученные от прибора, сканера требуют правильной интерпретации информации, дабы не тратить время и деньги на замену работающих элементов автомобиля.
Проблема зачастую кроется намного глубже чем кажется на первый взгляд. Это& вызвано теми обстоятельствами, что информационные сообщения содержат, как было выше сказано, косвенную информацию о нарушении работы системы.
Может быть полезным для решения вопроса по устранению неисправности у Nissan Murano (Z50):
Ошибка OBD-2 P0715 — проявляется в современных транспортных средствах с автоматической коробкой передач. Наличие данной ошибки характеризуется рывками в АКПП, отсутсвием сигнала от датчика входного вала при скорости больше 40 км/ч, и как следствие, загоранием на панели приборов лампочки «Check engine», которая может зажигаться и гаснуть в любой момент, как правило, во время движения автомобиля или при старте двигателя. Ошибка сигнализирует о неисправности проводки между датчиком и блоком управления двигателем и АКП, самого блока управления двигателем и автоматической коробкой передач, но скорее всего, о проблемах с датчиком частоты вращения входного вала, довольно часто его называют турбинным датчиком скорости.
Вышеуказанный датчик располагается под аккумуляторной батареей, и крепиться гайкой № 10. Замену неисправного датчика осуществляют на СТО, но можно сделать самому. Для этого необходимо снять аккумулятор, рожковым ключом на 10 открутить гайку крепления датчика и заменить неисправный датчик. Затем закрутить крепящую датчик гайку, и установить аккумуляторную батарею на место. После этого, ошибка исчезнет, так как неисправность устранена.
P0715 is a generic, and somewhat rare OBDII trouble code. If your Nissan Murano has P0715, it indicates there is a communication error with the sensor that measures transmission input speed.
Common Causes: A bad transmission speed sensor, shift solenoid, wiring issues, and even low/no transmission fluid can all cause P0715.
Here’s the definition of P0715 broken down by its two parts:
The input/turbine speed sensor measures the speed of the Nissan Murano’s transmission input shaft. It does this by measuring the speed of a reluctor wheel by using electromagnets.
The reluctor wheel will have notches cut into it. As the input shaft turns, the input/turbine speed sensor can tell each time one of these notches passes it.
It relays this data to the ECU or TCM, which uses it to determine input shaft speed. Then, your Murano’s PCM compares this data to engine RPM, the output shaft speed sensor, and the vehicle’s speed.
If the input/turbine speed reading doesn’t align with the variables listed above, a trouble code will be thrown, and the check engine light will come on.
The input/turbine speed sensor is usually screwed or bolted into the transmission case, so you won’t need to pull the transmission to service it.
The input/turbine speed sensor is sending a signal to the PCM that is out of range. Without knowing how fast the input shaft is spinning, the transmission will not shift properly (or at all), and your Tacom’s check engine light will illuminate with P0715.
Common symptoms of P0715 include:
Here’s a solid way to go about diagnosing P0715 in your Nissan Murano.
Check your Murano’s transmission fluid. Make sure that it is full. Low transmission fluid will cause the input shaft speed to increase in relation to the engine speed (it’ll slip).
Dirty transmission fluid can also cause P0715. Transmission fluid that’s burnt or dirty can’t efficiently do its job, which can cause the input speed to change in relation to the output speed. Transmission fluid color matters.
In this situation, input speed will be too high compared to the output speed and the vehicle speed.
The wiring going to your Murano’s input speed sensor can get damaged. Make sure that there is no frayed or damaged wiring. If there is, replace it.
Inspect where the harness plugs into the input speed sensor. Verify that it’s not visibly damaged. Do the pins look corrosion-free? They may need cleaning to make good contact.
Next, you’ll need to test the voltage and check the ground at the input/turbine speed sensor. There can only be two scenarios from here:
Repairing P0715 will usually involve the input/turbine speed sensor and its wiring, but internal transmission problems can cause it.
A bad valve body or shift solenoid can cause P0715.
P0715 is most commonly caused by a bad input/turbine speed sensor. Good luck repairing your Nissan Murano!
RECALLS! January 2022 Jason, “MAZDA6 shuts down while driving” fuel pump not monitored, may be no engine light etc. SEE…
I have a 2007 h3 hummer base model. Had transmission rebuilt (Pro).My problem is that when it gets around 35…
Adblock